Step Plumbing Guide for Installing a Bathtub
Step Plumbing Guide for Installing a Bathtub
Blog Article
The article listed below in relation to Installing A Bathtub is truly remarkable. Don't skip it.
Setting up a bath tub isn't exactly brain surgery, yet it does require strong plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old bath tub with a brand-new one is likewise a moderately challenging project. If the old tub is easily obtainable, the task can relocate immediately; if you need to open up a wall surface to eliminate the old tub and place the brand-new tub, the job is much harder. In either case, the job is within a residence handyman's skills, although you will require an assistant to move out the old tub and also embeded in the new one. See to it you have qualified yourself for the task and fit trying it. Instead of employing a specialist to take control of a halfway-completed job, it is better to take into consideration using one before you start. Chances are you might need a specialist plumber to make tube connections.
This write-up will certainly assist you mount a new bathtub in your shower room if you have currently acquired a brand-new tub as well as do not need to change the arrangement of your previous water supply pipes.
Your devices as well as material checklist should make up the following:
Removing Old Touches
If you need to change old taps with new ones as a part of your installation, then the first thing you need to do is detach the supply of water. After doing so, switch on the faucets to drain any type of water staying in the system. The process of removing the existing faucets can be rather troublesome as a result of the limited gain access to that is often the case.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipes to the faucets. Have a fabric prepared for the staying water that will originate from the pipelines. Once the supply pipes have actually been gotten rid of, make use of the same device to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from transforming during this process. As soon as the faucets have actually been eliminated, the holes in the bath/basin will need to be cleaned of any old securing compound.
Prior to proceeding to fit the new faucets, contrast the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will need a plastic adapter to prevent damages to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end offers a connection to the current supply pipes.
If you need to fit a monobloc, after that you will certainly need reducing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin making sure that the washing machines remain in area in between the tap and the sink. Protect the faucet in place with the producer supplied backnut. Once the tap is firmly in place, the supply pipes can be attached to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with typical faucet connectors. The previous type needs to be connected to the tap ends first, tightening only by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Mounting the Bath tub
Utilizing the two wood boards under its feet, position the bath tub in the called for placement. The wooden boards are handy in uniformly spreading the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto four small points.
The next objective is to ensure that the bath tub is leveled all round. This can be attained by inspecting the spirit level and changing the feet on the bathtub until the level reviews level.
To mount faucets, fit the bottom of the outermost adaptable tap adapter to the appropriate supply pipe by making a compression sign up with; after that do the very same for the various other tap.
Turn on the water system as well as inspect all joints and also new pipework for leaks and tighten them if required. Fill up the bathtub and likewise inspect the overflow outlet as well as the regular outlet for leakages.
Ultimately, repair the bathroom paneling as defined in the maker's user's manual. Tiling as well as sealing around the bath tub must wait till the tub has been used a minimum of when as this will certainly resolve it right into its last setting.
Preparing for the Setup
To start with, the supporting structure provided with the bath must be fitted (if required) according to the producer's directions. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is important to see to it that if the faucet includes a plastic washer, it is fitted in between the bath and the taps. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps unit to avoid stress on the bathtub.
Fit the adaptable tap connectors to the bottom of the two faucets utilizing 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet via the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you use every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom must currently prepare to be fitted in its final setting.
Tiling Around the Bathtub
In the area where the bath fulfills the floor tile, it is required to secure the joins with a silicone rubber caulking. This is important as the fitting can relocate sufficient to fracture a rigid seal, creating the water to penetrate the wall in between the bath and also the tiling, resulting in difficulties with dampness and possible leaks to the ceiling below.
You can select from a selection of coloured sealants to blend in your fixtures as well as fittings. They are sold in tubes and cartridges, and are capable of sealing spaces up to a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with twists of drenched paper or soft rope. Bear in mind to always fill up the bath tub with water before sealing, to allow for the activity experienced when the tub remains in use. The sealant can break relatively early if you do not take into consideration this activity prior to sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also quickly readily available on the marketplace. It is recommended to fit the tiles making use of water-resistant or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy more info about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Leave feedback down below. We would be pleased to know your responses about this write-up. We are looking forward to see you back again in the near future. So long as you liked our blog posting if you please do not forget to pass it around. Thanks a lot for your time. Visit us again soon.
Reliable every time! Report this page